![How To Install Mplayer Raspberry Pi How To Install Mplayer Raspberry Pi](https://www.electronicsforu.com/wp-content/uploads/2016/03/927_DBD_Fig_1.jpg)
- #HOW TO INSTALL MPLAYER RASPBERRY PI UPDATE#
- #HOW TO INSTALL MPLAYER RASPBERRY PI DRIVER#
- #HOW TO INSTALL MPLAYER RASPBERRY PI MANUAL#
- #HOW TO INSTALL MPLAYER RASPBERRY PI SOFTWARE#
To verify this, type in pactl list sinks short to check how many audio sinks available in your Pi. Once you successfully establish connection to your bluetooth speaker, you should be able to see new bluetooth audio sink available in the Pi.
![How To Install Mplayer Raspberry Pi How To Install Mplayer Raspberry Pi](https://i.pinimg.com/originals/c3/d0/90/c3d0903d993bad467b594d8504f16ed0.jpg)
You should see output " Attempting to connect to YY:YY:YY:YY:YY:YY Device YY:YY:YY:YY:YY:YY Connected: yes Connection successful" from terminal if connection is successful. Type in connect YY:YY:YY:YY:YY:YY to establish connection to bluetooth speaker.You should see a message " Device YY:YY:YY:YY:YY:YY Trusted: yes". Type in trust YY:YY:YY:YY:YY:YY to enable authentication-less connection with your bluetooth speaker.You will see a bunch of message and ends with message " Device YY:YY:YY:YY:YY:YY Paired: yes Pairing successful" if pairing successful. Type in pair YY:YY:YY:YY:YY:YY to pair with the bluetooth speaker.YY:YY:YY.YY is the bluetooth speaker mac address.
![How To Install Mplayer Raspberry Pi How To Install Mplayer Raspberry Pi](https://www.raspberrypi.org/app/uploads/2020/11/chr-800x710.png)
For my case my bluetooth speaker name is Blue Sync OR3. You should see a similar message " Device YY:YY:YY:YY:YY:YY BLUE SYNC OR3". Type in scan on to start scanning for bluetooth devices.
#HOW TO INSTALL MPLAYER RASPBERRY PI MANUAL#
(Follow your bluetooth speaker manual to set it to pairing mode) Turn on your bluetooth speaker and set it to pairing mode.If you see message from terminal state " Controller XX:XX:XX:XX:XX:XX Discoverable: no", just repeat step 5 to make your device discoverable again.The string XX:XX:XX.XX is your bluetooth dongle's mac address. You should see output " Changing discoverable on succeeded Controller XX:XX:XX:XX:XX:XX Discoverable: yes" from terminal. You need to key in this command to make sure your bluetooth dongle is visible to your bluetooth speaker. Type in discoverable on and press enter.You should see output " Default agent request successful" from terminal. Type in default-agent and press enter.You should see output " Agent registered" from terminal. You should see output " Changing power on succeeded" from terminal. You should see the next line in terminal start with # once you press enter. Type in bluetoothctl in terminal to enter bluetooth command line terminal.Next, it is time for us to setup the bluetooth speaker.
#HOW TO INSTALL MPLAYER RASPBERRY PI DRIVER#
0 means the unique id of your audio source, alsa_atform-soc_ is the name of your audio source, module-alsa-card.c is the driver name, s16le 2ch 44100Hz is audio source's sample specification and SUSPENDED means the audio source state is currently suspended. Here are some simple explanation on the output. If you see same output above in your Pi that means your PulseAudio is working properly.
#HOW TO INSTALL MPLAYER RASPBERRY PI UPDATE#
#HOW TO INSTALL MPLAYER RASPBERRY PI SOFTWARE#
The differences start on the software setup side. My hardware setup is the same as shown in my previous post. This method will work on Raspbian Jessie lite version as well. I finally found a proper procedure to setup bluetooth device in Raspbian Jessie using solely command line only. Totally crazy year for me last year.Īlright, for those who come from my previous post of bluetooth audio streaming using Raspberry Pi.